You may also like
ROCKWOOD Y106 Door Pulls with Base Plates
Material: Brass;
Finishes: UD26D;
Fastner: 1/4 - 20 x 2-1/2" thru bolt & finish washer (standard 1-3/4" door);
Options:
- Back to back mounting in pairs — use BTB suffix and mounting type number (Y107BTB5)
- Concealed mounting single pulls — use C suffix and mounting type number (Y107C6)
- Advise if door thickness is other than 1-3/4"
- See page B13 for mounting selection (standard duty 1/4 - 20)
ROCKWOOD OVERVIEW
Rockwood products are normally used on all types of institutional buildings, offices, retail, educational, detention, sports facilities, hotel and restaurant, and finer residences.
ENVIRONMENTAL MANAGEMENT
ASSA ABLOY is commited to protecting the quality of the environment as well as the health and safety of its employees, customers, and the community. Please see our Environmental Health and Safety Policy for details on how we are dedicated to this commitment.
RESOURCES & DOWNLOADS
Manufacturer Resources
Product Specs
- Subcategory:
- Push and Pull Plates, Door Pulls
- Product Group:
- Door Trim and Accessories
- Clearance:
- 1-5/8"
- Product Subgroup:
- Door Pulls, Push and Pull Plates
- Product Type:
- Door Pulls
- ANSI/BHMA:
- ANSI A156.6, J401
- Commercial/Residential:
- Commercial
- Product Model:
- Y106
- (CTC) Center-to-Center:
- 6"
- Product Projection:
- 2-3/8"
- Product Category:
- Door Trim and Accessories
- Department:
- Door Hardware
Rockwood ROC-Y106-626-BTB-5 – Frequently Asked Questions
1) What does the BTB-5 suffix on the Rockwood Y106 door pull actually get me?
BTB means back to back mounting in pairs, so you get pulls for both faces of one door, fastened through the door to each other. The 5 is the mounting type number. If you only want a pull on one face, that is the C suffix (concealed mounting, single pull) with its own mounting type number instead.
2) What is the closest equivalent to a Rockwood Y106 straight pull with a 3/4 inch round bar?
The Ives 8102HD is the nearest straight-pull counterpart: it is a heavy duty straight door pull built on a 3/4 inch round bar with 1-1/2 inch clearance. The Rockwood Y106 is also a 3/4 inch diameter straight pull, with 1-5/8 inch clearance and 2-3/8 inch projection, on 6 inch center-to-center, and it carries ANSI A156.6 J401. The practical difference is the clearance dimension, so if a glove-clearance or hand-clearance dimension was called out on the drawing, confirm which of the two matches before substituting.
3) I need a heavier bar than 3/4 inch for a high traffic entrance. What straight pull should I use instead of the Y106?
Step up to a 1 inch bar. The Ives 8103HD is a heavy duty straight door pull in 1 inch round with through bolt mounting, and the ABH AB3300 is a straight flat end commercial pull at 1.00 inch diameter. Both give you a larger grip section than the Y106's 3/4 inch bar. Note the Y106 ships as a back to back pair with base plates using 1/4-20 x 2-1/2 inch thru bolts and finish washers for a 1-3/4 inch door, so if you are replacing a back to back set you will need to confirm the mounting arrangement on the replacement.
4) Is a Deltana OHP620 back-to-back pull a substitute for the Rockwood Y106 BTB set?
Only on thinner doors. The Deltana OHP620 is an off-set handle pull supplied as a back-to-back set with a door thickness range of 1-1/8 inch to 1-3/8 inch. The Y106 back to back set is furnished with 1/4-20 x 2-1/2 inch thru bolts and finish washers sized for a standard 1-3/4 inch door. So on a typical 1-3/4 inch commercial door the two are not interchangeable, and the OHP620 is also offset rather than straight.
5) How much hand room is there behind the Rockwood Y106 pull, and how far does it stick off the door?
Clearance between the grip bar and the door face is 1-5/8 inches, and total projection off the door is 2-3/8 inches. That projection matters on a door swinging into a tight vestibule or beside a wall return, and on pairs where two leaves meet.
6) Does the Rockwood Y106 meet a commercial hardware spec for door pulls?
It is built to ANSI A156.6 and carries the J401 type designation, the standard that covers architectural door trim. It is a commercial-duty item, the kind of trim used on institutional, office, retail, educational, hotel and restaurant openings.
7) What is the Rockwood Y106 door pull made of and what finish does it come in?
Brass bar and plates, supplied in UD26D. The model as ordered here is the 626 satin chrome designation on brass, which is the common match for satin chrome push plates, hinges and lock trim already on a commercial opening.
8) Is a back to back pull the right choice, or do I want a push plate on one side?
Back to back makes sense when the door gets pulled from both faces, such as a cross-corridor or a double-acting opening. If the door only swings one way, most commercial specs run a pull on the pull side and a plate on the push side. For that, the Rockwood single pull with concealed mounting uses the C suffix, and a plate like the Trimco 1001-1 heavy duty push plate at 3 x 12 inches covers the other face.
9) Can I use a Trimco push plate on the push side instead of a second Y106 pull?
Yes, that is a common pairing on a swinging door. The Trimco 1001-1 is a heavy duty push plate at 3 inch by 12 inch, the 1041 is a half-round push plate at 8 inch by 16 inch, and the 1070 series offers classic push/pull plates at 3-1/2 inch by 15 inch. Any of these covers the push side while the Y106 pull, with its 6 inch center-to-center and base plates, handles the pull side. Just be aware the Y106 back to back arrangement thru-bolts through the door, so a push plate on the opposite face has to clear those fastener locations.
10) I need a much longer back-to-back pull than the Y106 for a glass entrance. What should I look at?
For long back-to-back sets, Deltana offers the SSPOBB24, a 24 inch back-to-back modern offset door pull, and the SSPORBB24, a 24 inch back-to-back round offset pull. Sure-Loc's PL-2KN is a knurled long door pull in a double-sided configuration. The Rockwood Y106 is a short 6 inch center-to-center pull, so these are a different grip length entirely rather than a direct swap.
11) What are the base plates on the Y106 for, and can I hide the bolts?
The Y106 is a pull with base plates, so the bar lands on a plate at each end rather than straight on the door face. That covers up the prep and spreads the load on a wood or hollow metal door. The back to back pairs version is through bolted with finish washers, so fasteners show; concealed mounting is the single-pull C option.
How fast can I get the Rockwood ROC-Y106-626-BTB-5 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Rockwood ROC-Y106-626-BTB-5 come with a warranty?
Absolutely. The Rockwood ROC-Y106-626-BTB-5 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Rockwood ROC-Y106-626-BTB-5?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Rockwood ROC-Y106-626-BTB-5 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.