Schaub 211081 Noho Square Cabinet Pull with 6" Center to Center and Standard Mounting

The Noho 211081 uses 8/32 machine screws, supplied at 1 inch long. That length covers a standard 3/4 inch drawer face or door with thread to spare. If you are mounting through a thicker slab front, a drawer box with a false front, or adding a backplate, you will need longer 8-32 screws.

The Schaub 211081 Noho is a contemporary square cabinet pull in brass with 6 inch center-to-center spacing and a 1-1/4 inch projection. For a shorter mounting spread in a similar modern square profile, the Deltana SBP35 Modern Square Bar Pull is a 3-1/2 inch solid brass pull, and the Omnia 1968/102 Modern Cabinet Pull is forged solid brass with 4 inch center-to-center spacing. Both use a squared modern bar form rather than the Noho detailing, so verify existing drill centers before swapping.

The Schaub 211081 Noho measures 7-1/2 inches overall on 6 inch centers, which needs a wide drawer front to look right. For narrow fronts, the Trimco 553 Series drawer pulls are set on 3 inch centers, and the Trimco 562 Series offers 3-1/2 inch, 4 inch, and 96mm center-to-center options. A knob is the other route on very narrow fronts: the Orca Hardware Blackcomb CK-17025 is a 25mm square cabinet knob, single-screw, which keeps the squared look of the Noho at much smaller scale.

Projection is 1-1/4 inches. That is enough grip clearance for a gloved hand and keeps the bar clear of the face for full-overlay doors. Where the pull sits near an inside corner or beside an appliance, check that 1-1/4 inches plus the door swing will not collide.

Five: Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass. Unlacquered Brass is the one to specify if you want the pull to darken and patina with use; the others hold their look. For a kitchen where every pull has to match, order the whole run in one finish at once.

Brass is the base material, not zinc die cast. That matters for the Unlacquered Brass and Vintage Brass options in particular, since the finish is on brass underneath rather than a plated substrate, and it holds up better to repeated hand contact in a kitchen or a multi-family turn.

No. Both sit in the Schaub design family - the Emtek Bar Cabinet Pull is part of Emtek's Schaub Collection - but the Bar pull is a round bar profile in Emtek's Bar series, while the 211081 belongs to Schaub's NOHO collection with a squared contemporary profile. Emtek also offers the Alexander and Art Deco cabinet pulls in the Schaub Collection, both catalogued as cabinet knob/pull, plus the Emtek 8405 Select cabinet pulls. If the design intent on the drawing is the Noho square, none of those substitute visually.

The Schaub 211081 Noho is a brass pull offered in Matte Black, Polished Nickel, Unlacquered Brass, Satin Brass, and Vintage Brass. If a facility standard calls for steel instead of brass, the Orca Hardware CK-12001 T-Pull Bar is a steel pull with a 2 inch bar width in satin nickel. The Deltana SBP35 is described as heavy-duty solid brass if you want to stay in brass but in a bar profile.

Yes, that is a common split - pulls on drawers and knobs on doors. The 211081 Noho is a two-hole pull on 6 inch centers using 8/32 x 1 screws. For single-hole knobs in the same job, the Orca Hardware Bachelor CK-15030 is a round cabinet knob at 1-1/4 inch diameter, the Bachelor CK-16030 is a round ring knob at 1-1/4 inch diameter, and the Blackcomb CK-17025 is a 25mm square knob. Match the finish family across both, since the Noho finish list and the Orca finishes are specified separately.