Schaub 216 5" Center to Center Northport Square Cabinet Pull

Yes. The Northport 216 square pull is drilled on 5 inch center-to-center spacing, so it lands on existing 5 inch bores with no new holes. Overall length is 6 inches, which means it overhangs the mounting holes by about a half inch at each end, so check you have that much clear face on a narrow drawer rail.

It uses 8/32 thread screws, 1 inch long, which is the standard cabinet pull thread. A 1 inch screw covers a typical 3/4 inch drawer front with enough thread left to engage the post. If you are going through a thicker slab front or a front with an applied panel, you will need longer 8/32 screws.

The base material is zinc, finished in the color you select. Zinc die cast holds crisp square corners well, which is what gives the Northport its flat-sided profile. If a spec calls specifically for solid brass, the Omnia 1969 and Omnia 1971 modern pulls are forged solid brass and both carry the same 1-3/16 inch projection.

The Schaub 216 Northport pull is built on a zinc base material in a transitional square profile at 5 inch center to center. If you want a forged solid brass body instead, the Omnia 1969 modern cabinet pull carries the same 1-3/16 inch projection as the Schaub 216 in forged solid brass, and the Omnia 1971 is also forged solid brass at 1-3/16 inch projection. The Deltana SBP35 is another solid brass option, a heavy-duty modern square bar pull at 3-1/2 inch center to center, so it sits closer to the cabinet doors than the 5 inch spacing of the 216.

The Schaub 216 Northport pull is fixed at 5 inch center to center with an overall length of 6 inches, so it will not land on existing 4 inch holes. For a 4 inch drilling, the Omnia 1968/102 modern cabinet pull is specified at 4 inch center to center in forged solid brass. The Trimco 562 series drawer pulls are offered in 3-1/2 inch, 4 inch, and 96mm center to center, which covers both a 4 inch layout and the metric 96mm spacing common on imported cabinetry.

Projection is 1-3/16 inches from the face of the door or drawer to the back of the grip. That is enough knuckle clearance for a gloved hand, and it matters on inset cabinetry or anywhere a pull sits near a wall return or an adjacent appliance door swing. The base footprint measures 1 inch.

Eight finishes: Satin Nickel, Brushed Nickel, Polished Nickel, Polished Chrome, Ancient Bronze, Brushed Bronze, Matte Black, and Signature Satin Brass. That spread covers both the cool and warm sides of a job, so you can run one collection through a kitchen, a butler's pantry, and a bath without switching hardware lines.

They are related but not interchangeable. The Schaub 216 is the Northport collection square pull at 5 inch center to center with a 1-3/16 inch projection. Emtek offers several Schaub Collection cabinet pulls under its own part numbers, including the Emtek 8405 Select cabinet pulls, the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull, each a distinct series. If a specification calls out Northport specifically, order the Schaub 216 rather than substituting an Emtek Schaub Collection series.

Schaub classes the Northport as transitional, not contemporary. The square bar reads clean enough for a flat-slab door but the proportions carry on a shaker front too, which is why it gets specified in remodels where the cabinetry is traditional and the finishes are current. For a strictly modern look, the Deltana SBP35 modern square bar pull or the Omnia 1968/102 modern pull are the sharper-edged alternatives.

The pull is specified with 8/32 thread by 1 inch screws. On a multi-unit or property job where fronts vary in thickness, order a box of longer 8/32 machine screws alongside so you are not stopped mid-install on the thicker fronts.

Yes, Schaub publishes a Proposition 65 warning for this pull through their product stewardship page. If you are buying for a California job or a spec that requires the disclosure on file, flag it at the order stage.

The Schaub 216 Northport pull is offered in satin nickel along with polished chrome, ancient bronze, brushed bronze, brushed nickel, matte black, polished nickel, and signature satin brass. The Orca Hardware CK-12001 T-pull bar is a steel pull supplied in satin nickel, so the finish names line up, but it is a different base material than the zinc body of the 216 and a different profile, a 2 inch wide bar pull rather than a square Northport pull. Order a sample of each before committing if the two will sit on adjacent cabinetry.