Schaub 244-320 320mm Center to Center Wave Cabinet Pull

Drill the two mounting holes 320 mm apart on center. That is the 244-320's fixed center-to-center dimension, so existing cabinet fronts already bored at 320 mm accept it directly. The pull itself runs 14-1/4 inches overall, so allow for the extra length beyond the screw holes when laying out drawer fronts.

It takes M4 metric machine screws, not the 8-32 screws common on US cabinet hardware. If you are mixing this pull into a run of American-threaded hardware, keep the metric screws with it. On thicker drawer fronts or slab doors you will need longer M4 screws than the ones supplied.

The Schaub 244 Wave pull uses a zinc base material. If your spec calls for brass, the Omnia 1968/102 modern cabinet pull is forged solid brass with 4 inch center-to-center spacing, and the Omnia 1969, 1970, and 1971 modern pulls are also forged solid brass, with 1-3/16 inch, 1-1/4 inch, and 1-3/16 inch projections respectively. The Deltana SBP35 modern square bar pull is a heavy-duty solid brass pull at 3-1/2 inches. All of these are shorter than the 320 mm Schaub, so plan the drawer layout accordingly.

The Schaub 244 Wave pull is built around 320 mm center-to-center with a 14-1/4 inch overall length, so it is sized for wide drawers and tall appliance panels. For small drawers, the Trimco 553 Series drawer pull is offered at 3 inch center-to-center, and the Trimco 562 Series is offered in 3-1/2 inch, 4 inch, and 96 mm center-to-center. Those shorter spacings let you keep a consistent look on narrow fronts where a 320 mm pull would not fit the drawer face.

Projection is 1 inch. That is enough clearance for a gloved hand on a kitchen or bath cabinet, and it keeps the pull tight to the face in a galley or narrow hallway where a deeper bar pull would catch clothing. In an appliance-panel situation, check the 1 inch against any adjacent handle before committing.

Four finishes: Satin Nickel, Polished Chrome, Matte Chrome, and Matte Black. Satin Nickel and Matte Black are the usual choices for standardizing across a multi-family or hospitality build; Matte Chrome gives a low-sheen silver if the plumbing trim is brushed rather than polished.

The Wave is a collection, and the 244-320 is the 320 mm center-to-center size within it. Order the shorter Wave center-to-center sizes for upper doors and small drawers so the profile stays consistent across the kitchen, and reserve the 320 mm for the wide drawers and tall pantry doors.

They are related but not interchangeable. The Schaub 244 belongs to the Wave collection and is a cabinet pull at 320 mm center-to-center. Emtek offers several Schaub Collection cabinet knob/pull lines under different series names, including Emtek SELECT (8405), Alexander, Art Deco, and Bar. Those are separate series with their own designs, so ordering an Emtek Schaub Collection pull will not give you the Wave profile or that 320 mm spacing unless the Emtek series is specified at the same dimension.

The Schaub 244 Wave is a contemporary-style pull with a curved wave profile and a 1 inch projection. If you want the same modern look in a straight bar, the Emtek Bar cabinet pull in the Schaub Collection and the Deltana SBP35 modern square bar pull are both bar-form pulls, the Deltana at 3-1/2 inches in solid brass. The Orca Hardware CK-12001 T-pull bar is a steel bar pull with a 2 inch bar width in satin nickel. Confirm center-to-center before you drill, since none of these match the 320 mm spacing of the Wave.

Only where a single mounting hole suits the door. The Schaub 244 Wave is a two-post pull at 320 mm center-to-center with M-4 metric screws, so it needs two bores. Knobs such as the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter, the Bachelor round ring knob at 1-1/4 inch diameter, and the Blackcomb Collection square knob at 25 mm diameter mount on a single fastener. They are a common choice for upper doors while long pulls carry the wide drawers below.

The Schaub 244 Wave pull has a 1 inch projection off the face of the door. For more knuckle room, the Omnia 1970 modern cabinet pull carries a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 modern pulls each carry a 1-3/16 inch projection, all in forged solid brass. That extra clearance matters on gloss fronts and in gloved-hand settings.

Emtek carries Schaub-designed cabinet hardware under its SELECT program, including the Emtek 8405 Select cabinet pulls and the Bar, Alexander, and Art Deco cabinet pulls from the Schaub collection. Those are the route if a project is already specified in Emtek. The Wave profile itself is a contemporary Schaub design and the 244-320 is the 320 mm version of it.

No. The SDC SP50 is a 50 mm spindle used in door control hardware, not cabinet trim. The Schaub 244 Wave is a cabinet pull that mounts through the drawer or door front on M-4 metric screws at 320 mm center-to-center. The two parts serve different hardware entirely and share no mounting interface.