Schaub 442 160mm Center to Center Flared Rectangular Finestrino Cabinet Pull

Yes. The Schaub 442 Finestrino pull is drilled on 160 mm center-to-center, the standard metric spacing for wider drawer pulls, so it lines up with existing 160 mm holes with no new boring. Overall length is 7 inches, so the pull covers a bit more than the hole span on each end.

The Schaub 442 Finestrino pull is built on a zinc base material with a 160 mm center-to-center spacing and a 3/4 inch projection. If the specification calls for forged solid brass in a modern profile, the Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, which is the nearest inch-based hole spacing rather than a metric 160 mm match. The Omnia 1969 and 1971 are also forged solid brass modern pulls, each with a 1-3/16 inch projection, and the Omnia 1970 is forged solid brass with a 1-1/4 inch projection. Note that all three of those Omnia pulls stand off the door face further than the 3/4 inch projection of the 442, so finger clearance and any adjacent appliance swing should be checked before substituting.

The Schaub 442 Finestrino pull measures 7 inches by 2-1/8 inches overall on a 160 mm center-to-center drilling, which is too wide for narrow doors and small drawer fronts. For shorter spacings, the Trimco 553 series drawer pull is offered at 3 inch center-to-center, and the Trimco 562 series is offered in 3-1/2 inch, 4 inch, and 96 mm center-to-center options, so 96 mm gives you a metric step down. The Deltana SBP35 is a 3-1/2 inch modern square bar pull in solid brass for a similar squared-off look at a shorter length. For the narrowest fronts, a knob eliminates the spacing question entirely: the Orca Hardware CK-15030 Bachelor round cabinet knob and the CK-16030 round ring knob are both 1-1/4 inch diameter, and the CK-17025 Blackcomb square knob is 25 mm.

Projection is 3/4 inch. That is a slim standoff, enough for fingers behind a flared rectangular grip but tight if you want a full-hand grab. If you need more clearance on a heavy drawer, a deeper option like the Omnia 1970 at 1-1/4 inch projection or the Omnia 1969 at 1-3/16 inch gives more room.

Five finishes: Satin Nickel, Polished Chrome, Matte Chrome, Burnished Bronze, and Matte Black. Matte Chrome and Polished Chrome let you match either a brushed or bright plumbing suite in the same room, and Matte Black pairs with the black faucet and appliance packages common in current kitchen specs.

The base material is zinc, finished in one of five plated or coated colors. Solid brass alternatives include the Deltana SBP35 square bar pull and the Omnia 1968/102 and 1971 pulls, all forged or solid brass, if a brass substrate is called out on the spec.

Two things drive the rollout. The 160 mm center-to-center spacing has to match the drilling pattern on the cabinet package, and the fasteners are M4 metric, so the maintenance stock room needs M4 screws, not 8-32. The zinc body with a plated finish is a cost-efficient choice for volume; where a brass substrate is required by spec, the Deltana SBP35 or the Omnia 1968 through 1971 pulls are solid brass options.

Yes, and the styling relationship is direct: Emtek sells several cabinet pull lines under its Schaub Collection, including the Emtek 8405 Select cabinet pulls, the Alexander cabinet pull, the Art Deco cabinet pull, and the Bar cabinet pull, all catalogued as cabinet knob/pull function. The Schaub 442 belongs to the Finestrino collection in a contemporary style, so the Emtek Bar and Select lines are the most visually compatible of that group for a modern run. Confirm hole spacing before mixing on the same drawer bank, since the 442 drills at 160 mm center to center.

They are not interchangeable. The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width, built in steel and supplied in satin nickel, while the Schaub 442 Finestrino is a zinc-base flared rectangular pull with a 7 inch by 2-1/8 inch footprint and M4 screw threads. The 442 is also offered in satin nickel along with polished chrome, matte chrome, matte black, and burnished bronze, so if the job is matching a satin nickel run of Schaub pulls, stay within the 442 rather than crossing to the steel T-pull, whose profile and mounting differ.

Yes. The 442 belongs to Schaub's Finestrino collection in a contemporary style, so it reads clean and squared off. Pairing pulls on drawers with knobs on doors is standard practice; round or square contemporary knobs such as the Orca Bachelor round knob at 1-1/4 inch diameter or the Blackcomb square knob at 25 mm keep the same modern line.

The grip is rectangular in section and flares out toward the ends rather than running a constant round bar. Compared with a straight tube pull like the Emtek Bar cabinet pull or a T-shaped bar such as the Orca CK-12001, the flat faces give a broader contact surface for the fingers and a more architectural profile against a slab door.

No. The SDC SP50 is a 50 mm spindle classified as a door control component, not cabinet hardware. The Schaub 442 Finestrino is a cabinet pull with 160 mm center-to-center hole spacing and M4 mounting screws for drawer fronts and cabinet doors. If you need a cabinet pull, stay with the 442 or another cabinet pull line such as the Emtek Bar cabinet pull in the Schaub Collection.