Schaub 445 128mm Center to Center Rectangular Finestrino Cabinet Pull

The Schaub 445 Finestrino pull is drilled at 128 mm center to center, so it will not land on a 96mm hole pattern. The Trimco 562 Series drawer pull is offered in a 96mm center to center option along with 3-1/2 inch and 4 inch spacings, which matches an existing 96mm pair of holes without redrilling. For a shorter existing pattern, the Trimco 553 Series drawer pull is a 3 inch center to center part.

The Schaub 445 Finestrino pull uses a zinc base material in a contemporary rectangular form. If the job calls for brass, the Deltana SBP35 is a modern square bar pull in solid brass at 3-1/2 inch, and the Omnia 1968/102 is a modern cabinet pull in forged solid brass at 4 inch center to center. Both sit at a different hole spacing than the 128 mm Finestrino, so plan the drilling accordingly on new doors.

Machine screws are M4, the metric standard on this pull. Standard-length M4 screws suit a typical 3/4 inch front. If you are mounting through a thicker front, a backer, or a slab door, order longer M4 screws separately, since the threading is what has to match, not the head.

Projection is 7/8 inch. That is enough grip clearance for a gloved hand and keeps the pull tight to the face in a galley or a tight island run where a deeper pull catches hips and pockets. If you want more knuckle room, the Omnia 1969 and 1971 pulls are listed at 1-3/16 inch projection and the Omnia 1970 at 1-1/4 inch.

Base material is zinc, a cast alloy that holds a plated finish well and takes daily cabinet duty in an apartment or spec kitchen. If your spec calls for solid brass instead, the Deltana SBP35 square bar pull and the Omnia 1968, 1969, 1970 and 1971 pulls are forged or solid brass options.

Five finishes: Satin Nickel, Polished Chrome, Burnished Bronze, Matte Chrome and Matte Black. Matte Chrome and Polished Chrome are distinct here, so if you are matching a faucet or appliance pull, pick by sheen as well as color. Burnished Bronze is the only warm-tone option in the run.

The 445 is part of Schaub's Finestrino collection in a rectangular contemporary profile, 128 mm centers, 7/8 inch projection. If the existing pulls in your unit are Finestrino at a different center-to-center, the profile matches but the hole pattern will not, so order by both collection and centers when you are standardizing a building.

The Schaub 445 Finestrino stands 7/8 inch off the door face. Among modern cabinet pulls, the Omnia 1970 projects 1-1/4 inch, and the Omnia 1969 and Omnia 1971 each project 1-3/16 inch, all in forged solid brass. Where a pull sits next to an adjacent door, a return panel, or an appliance handle, that projection figure is the number to check before ordering.

The Schaub 445 is a two-hole pull on 128 mm centers with M4 screws, which suits a wider drawer face. On narrow drawers or small doors where a single bore is easier, the Orca Hardware Bachelor Collection round cabinet knob CK-15030 is 1-1/4 inch in diameter, the CK-16030 is a 1-1/4 inch round ring knob, and the Blackcomb CK-17025 is a square knob at 25mm. Knobs are a one-hole prep, so they will not reuse an existing 128 mm hole pair.

The Schaub 445 Finestrino is a zinc pull with a 7/8 inch projection, supplied in Satin Nickel, Polished Chrome, Burnished Bronze, Matte Chrome and Matte Black. Where a facility standardizes on steel, the Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel, and the Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inch. Matching the finish family across a run matters more than the material choice when the two are mixed on the same elevation.

A pull spans two screw holes and gives you a full-hand grip, which is what you want on wide drawers and heavy roll-outs. A knob is a single center hole, faster to install and better suited to small doors and upper cabinets. Switching from knobs to the 445 means drilling a second hole at 128 mm spacing on every front. Knob options include the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter and the Blackcomb square knob at 25mm.