Pop-In - Round 5CCT Remodel Downlight
Features
- Delivered Lumens: Up to 1080lm
- CBCP: Up to 1309
- 2700K/3000K/3500K/4000K/5000K
- CRI: 90
- Power: 12W
- Input: 120-277 VAC, 50/60Hz
- IC Rated, Airtight
- ELV Dimming: 100-5%
- TRIAC Dimming: 100-5%
- Rated Life: 50000 Hours
- Construction: Die-cast Aluminum with 20-gauge Cold Rolled Steel Junction Box
- 5-CCT Switchable between 2700K and 5000K
- Electrical box located on back of fixture to allow easy installation
- Sold as remodel, but new construction frame available
- Driver concealed within the fixture
Manufacturer Resources
Product Specs
- Product Group:
- Indoor Lighting
- Brand Family:
- WAC Limited
- Subcategory:
- Ceiling Lighting
- Segment:
- Lighting
WAC Lighting R4DRDR-F9CS-BK – Frequently Asked Questions
1) Can the WAC Pop-In 4 inch round downlight be installed in an existing ceiling without opening up the drywall?
Yes. The Pop-In 4 inch round 5CCT downlight is sold as a remodel fixture, so it goes into an existing ceiling cutout. The electrical box sits on the back of the fixture, which means you wire it at the opening rather than pulling a separate can or J-box into the cavity. A new construction frame is available if you are roughing in before the ceiling goes up.
2) Is the WAC Pop-In 4 inch downlight safe to install in a ceiling with insulation against it?
Yes. The Pop-In 4 inch round downlight is IC rated, so insulation can contact the housing directly, and it is airtight, so it will not leak conditioned air into an attic. That combination is what you need for an insulated ceiling below an unconditioned attic without building a separate insulation dam.
3) How do you change the color temperature on the WAC Pop-In 4 inch 5CCT downlight?
The fixture is field switchable across five color temperatures: 2700K, 3000K, 3500K, 4000K and 5000K. You set it at the fixture during install, so one part number covers a warm 2700K residential unit and a 5000K back-of-house or garage unit. For property managers that means one SKU on the truck instead of five, and you can match new fixtures to whatever the rest of the building is already running.
4) Will the WAC Pop-In 4 inch downlight run on 277 volt commercial power?
Yes. Input is 120-277 VAC, 50/60Hz, so the same fixture works on 120V residential circuits and on 277V lighting branch circuits in commercial buildings. The driver is concealed inside the fixture, so there is no remote driver to find a home for above the ceiling.
5) What kind of dimmer works with the WAC Pop-In 4 inch LED downlight?
It dims on ELV and on TRIAC (forward phase) dimmers, 100 percent down to 5 percent on either. There is no 0-10V control input, so if your project is specced around a 0-10V control system this is the wrong fixture. On a retrofit where you are keeping an existing TRIAC wall dimmer, it will work, though LED-rated dimmers with a low enough minimum load are what get you to the bottom of the range.
6) How much light does a 4 inch WAC Pop-In downlight put out, and is it enough for general room lighting?
Up to 1080 delivered lumens from 12 watts, with center beam candlepower up to 1309. That is a general-purpose output for a 4 inch aperture: enough for kitchens, corridors, offices and unit lighting at normal spacing. CRI is 90, so color rendering holds up in retail, healthcare and hospitality spaces where 80 CRI product gets rejected.
7) What finishes and pack sizes does the WAC Pop-In 4 inch round downlight come in?
Two trim finishes: white and black. White is also sold in multi-packs, a 4 pack and a 12 pack, which is the practical way to buy for a whole unit turn or a floor of offices. Black is a single unit.
8) How long does the WAC Pop-In LED downlight last before it needs replacing?
Rated life is 50,000 hours. Run 12 hours a day in a corridor or common area, that is roughly 11 years of service. The LED and driver are integral to the fixture, so at end of life you replace the unit rather than a lamp, which is the tradeoff for the slim remodel build.
9) Is the WAC Pop-In 4 inch downlight durable enough for commercial and multi-family use?
The housing is die-cast aluminum and the junction box is 20-gauge cold rolled steel, not plastic. Die-cast aluminum also acts as the heat sink for the LED, which is what protects the 50,000 hour rating in a ceiling with insulation packed around it.
10) Where do I find the cutout size and wiring instructions for the WAC Pop-In R4DRDR downlight?
WAC publishes both an installation guide and a specification sheet for the R4DRDR round 5CCT remodel downlight, and both are linked on the product record. The installation guide covers the ceiling opening and the wiring sequence at the back-mounted box; the spec sheet carries the photometrics and physical dimensions for submittal.
How fast can I get the WAC Lighting R4DRDR-F9CS-BK delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the WAC Lighting R4DRDR-F9CS-BK come with a warranty?
Absolutely. The WAC Lighting R4DRDR-F9CS-BK is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the WAC Lighting R4DRDR-F9CS-BK?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the WAC Lighting R4DRDR-F9CS-BK from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.