You may also like
ROCKWOOD 105 Door Pulls
Material: Stainless Steel;
Finishes: UD32D;
Fastner: 1/4 - 20 x 2-1/2" thru bolt & finish washer (standard 1-3/4" door);
Options:
- Back to back mounting in pairs — use BTB suffix and mounting type number (107BTB5)
- Concealed mounting single pulls — use C suffix and mounting type number (107C6)
- Advise if door thickness is other than 1-3/4"
- See page B13 for mounting selection (standard duty 1/4 - 20)
- 2-1/2" Barrier Free clearance — use BF prefix (BF107)
ROCKWOOD OVERVIEW
Rockwood products are normally used on all types of institutional buildings, offices, retail, educational, detention, sports facilities, hotel and restaurant, and finer residences.
ENVIRONMENTAL MANAGEMENT
ASSA ABLOY is commited to protecting the quality of the environment as well as the health and safety of its employees, customers, and the community. Please see our Environmental Health and Safety Policy for details on how we are dedicated to this commitment.
RESOURCES & DOWNLOADS
Manufacturer Resources
Product Specs
- Product Group:
- Door Trim and Accessories
- Clearance:
- 1-7/8"
- Subcategory:
- Push and Pull Plates, Door Pulls
- Product Subgroup:
- Door Pulls, Push and Pull Plates
- Product Type:
- Door Pulls
- ANSI/BHMA:
- ANSI A156.6, J401
- Commercial/Residential:
- Commercial
- Product Model:
- 105
- (CTC) Center-to-Center:
- 5-1/2"
- Product Projection:
- 2-5/8"
- Product Category:
- Door Trim and Accessories
- Department:
- Door Hardware
Rockwood 10532D – Frequently Asked Questions
1) Will the Rockwood 105 door pull fit a 1-3/4 inch door, and what happens if my door is thicker?
The 105 pull ships with 1/4-20 x 2-1/2 inch thru bolts and finish washers sized for a standard 1-3/4 inch door. If your door is thicker or thinner, say so when you order so Rockwood supplies the right bolt length. Thru bolting means the pull pulls against both faces of the door, so the fastener length has to match the actual thickness.
2) How far does the Rockwood 105 pull stick out from the door, and how much hand room is behind it?
Projection is 2-5/8 inches off the face of the door with 1-7/8 inches of clearance between the bar and the door. That 1-7/8 inch gap is what your fingers get. If you need more knuckle room, Rockwood offers a 2-1/2 inch barrier free clearance version using the BF prefix.
3) Can I mount Rockwood 105 pulls back to back on both sides of a door?
Yes, but it is an ordering change, not a field decision. Back to back pairs use the BTB suffix with the mounting type number (Rockwood shows it as 107BTB5). For a single pull with no fasteners showing on the opposite face, order the C suffix concealed mounting with the mounting type number instead. Decide this before the order goes in, since it changes the fasteners supplied.
4) What is the closest straight door pull to the Rockwood 105 with the same 3/4 inch bar diameter?
The Ives 8102HD heavy duty straight door pull uses the same 3/4 inch round bar as the Rockwood 105, so the two carry a similar grip feel in the hand. The difference is clearance: the Ives 8102HD is built to 1-1/2 inch clearance, while the Rockwood 105 runs 1-7/8 inch clearance with a 2-5/8 inch projection and 5-1/2 inch center-to-center mounting. If the opening was drilled for the 105, confirm the hole spacing before treating the 8102HD as a drop-in.
5) What straight pull should I use if I want a heavier 1 inch bar instead of 3/4 inch?
Step up to the Ives 8103HD heavy duty straight door pull, which uses a 1 inch round bar with through bolt mounting, or the ABH AB3300 straight flat end commercial door pull at 1.00 inch diameter. Both keep the straight bar shape of the Rockwood 105 while putting more material in the hand for high traffic entrances. The Rockwood 105 itself is a 3/4 inch diameter pull mounted 5-1/2 inch center-to-center with 1/4-20 x 2-1/2 inch thru bolts and finish washers for a standard 1-3/4 inch door.
6) The Rockwood 105 is a straight pull. What do I use when the opening needs an offset pull instead?
For an offset shape, the ABH AB3310 offset flat end door pull is a surface mount commercial handle, the ABH AB3330 offset round end pull is offered with custom length options, and the Ives 8169 is a C style offset solid pull at 1 inch diameter with heavy duty mounting. An offset changes where the hand sits relative to the door face, so it is a different mounting layout than the Rockwood 105 straight bar at 5-1/2 inch center-to-center, not a bolt-for-bolt swap.
7) I need an ADA compliant pull for an accessible entrance. Is there an alternative to the Rockwood 105?
The Ives 8145EZHD is a 45 degree offset door pull described as ADA compliant, supplied with heavy duty mounting hardware. The Rockwood 105 is built to ANSI A156.6, J401 with 1-7/8 inch clearance; where a project calls for the 2-1/2 inch barrier free clearance, Rockwood handles that with a BF prefix on the pull number. Which route you take depends on whether the specification names a clearance dimension or an offset handle shape.
8) Can I use a Deltana OHP620 or SSPOBB24 in place of the Rockwood 105?
They serve different openings. The Deltana OHP620 off-set handle pull is sold as a back-to-back set with a door thickness range of 1-1/8 inch to 1-3/8 inch, while the Rockwood 105 is fastened with 1/4-20 x 2-1/2 inch thru bolts sized for a standard 1-3/4 inch door. The Deltana SSPOBB24 is a 24 inch back-to-back modern offset pull and the SSPORBB24 is its round offset counterpart, both long-format handles rather than a 5-1/2 inch center-to-center grab pull. If the door is 1-3/4 inch commercial construction, the Deltana thickness range is the thing to check first.
9) Does the Rockwood 105 pull meet ANSI standards for a commercial opening?
It is built to ANSI A156.6, type J401, and is a commercial grade item. That is the standard covering architectural door trim, so it is the citation a spec writer or facility buyer is looking for on a submittal.
10) What is the Rockwood 105 pull made of, and will it hold up on a high traffic entrance?
Stainless steel bar, supplied in US32D satin stainless. Rockwood trim of this kind goes on institutional buildings, offices, retail, schools, detention, sports facilities, hotels and restaurants. Satin stainless is the finish most property managers standardize on across a building because it hides handling and matches existing push plates and kick plates.
11) Should I use a straight pull like the Rockwood 105 or an offset pull?
A straight bar pull like the 105 sits parallel to the door with the same 1-7/8 inch clearance the whole length, and it is the simplest thing to standardize across a lot of doors. An offset pull angles the grip away from the face at one end, which suits a door where you want the hand approaching from a different angle. If you want offset instead, ZenSupply carries the ABH AB3310 flat end offset pull, the ABH AB3330 round end offset, and the Ives 8145 45 degree offset. For a straight bar in a larger diameter, the Ives 8103HD is a 1 inch round straight pull with through bolt mounting.
12) What is the closest alternative to a Rockwood 105 straight pull if I need a different bar diameter?
The 105 is a 3/4 inch diameter straight bar. For the same straight bar shape in other diameters, the Ives 8102HD is a heavy duty 3/4 inch round straight pull with 1-1/2 inch clearance, the Ives 8103HD is 1 inch round with through bolt mounting, the ABH AB3300 is a 1 inch diameter straight flat end pull, and the ABH AB7200 is solid stainless at 7/8 inch diameter with through bolt mounting. Note the 8102HD's 1-1/2 inch clearance is tighter than the 105's 1-7/8 inches, which matters if hand room is the reason you are looking.
13) Is the Rockwood 105 pull the right choice for a residential entry door?
Probably not. The 105 is a commercial item and its fastening is set up for a 1-3/4 inch door, which is the commercial standard, not the thinner doors common on interior residential openings. For a residential thickness, the Deltana OHP620 offset handle pull is a back to back set listed for 1-1/8 to 1-3/8 inch doors. If you want a decorative pull on a finer residence, ZenSupply carries the Emtek 8 inch pulls in Baden, Brisbane, Arts and Crafts, and cast bronze Art Nouveau.
14) I need a pull on one side and a push on the other. Does the Rockwood 105 cover both?
No. The 105 is a pull bar only, so the push side needs a separate plate. ZenSupply carries the Trimco 1001-1 heavy duty push plate at 3 by 12 inches, the Trimco 1041 half round push plate at 8 by 16 inches, and the Trimco 1070 Series classic push and pull plates at 3-1/2 by 15 inches if you want the pull mounted on a plate rather than direct to the door.
15) Does the Cal-Royal PUL-175 do the same job as the Rockwood 105?
No. The Cal-Royal PUL-175 is a night latch cylinder pull, 3-1/2 inch height in stainless steel, meaning it is drilled to sit over a rim cylinder on a night latch installation. The Rockwood 105 is a plain straight pull with 5-1/2 inch center-to-center mounting and no cylinder provision. If the door has a rim cylinder that has to pass through the pull, the 105 is not the part.
16) I want a through-bolted stainless pull close to 3/4 inch but a little heavier. What is between the Rockwood 105 and a 1 inch bar?
The ABH AB7200 is a solid stainless steel flat end pull handle at 7/8 inch diameter with through-bolt mounting, sitting between the Rockwood 105 at 3/4 inch diameter and the 1 inch bars. Both are through-bolted stainless; the Rockwood 105 ships with 1/4-20 x 2-1/2 inch thru bolts and finish washers sized for a 1-3/4 inch door, so verify door thickness before ordering either.
17) For a restroom door, is the Trimco 1035 a better choice than the Rockwood 105?
The Trimco 1035 Ultimate Restroom Pull is a heavy duty pull built specifically for restroom doors, where the Rockwood 105 is a general purpose straight pull at 5-1/2 inch center-to-center used across institutional, office, retail, educational, hotel and restaurant openings. If the restroom door is being specified as part of a wider hardware package that already standardizes on straight pulls, the 105 keeps the fleet consistent; if the restroom opening is being addressed on its own, the 1035 is purpose-built for it.
18) I need a back-to-back pull pair on one door. Do I order the Rockwood 105 or a different product?
The Rockwood 105 handles back-to-back mounting through its own ordering suffix: pulls are mounted in pairs using the BTB suffix with the mounting type number, and concealed mounting on single pulls uses the C suffix with the mounting type number. If instead you want a product supplied as a back-to-back set out of the box, the Deltana OHP620 off-set handle pull is sold that way for doors 1-1/8 inch to 1-3/8 inch thick, and the Deltana SSPOBB24 is a 24 inch back-to-back set.
19) What model do I actually order for a Rockwood 105 in satin stainless?
Order it as 10532D. That is the 105 pull in the US32D satin stainless finish, and it is the single configuration this pull is stocked in.
20) Does the Rockwood 105 pull need a mounting type specified when ordering?
Yes for anything other than a plain single pull. Rockwood mounting selections are standard duty 1/4-20 and are listed on page B13 of their catalog; the BTB back to back and C concealed options both take a mounting type number appended to the suffix. Straight single pull with thru bolts and finish washers is what you get if you specify nothing.
21) Which long pull should I use on a glass or storefront style entrance instead of the Rockwood 105?
The Deltana SSP1210 is a 12 inch contemporary pull for single side mounting, and the SSPOBB24 and SSPORBB24 are 24 inch back-to-back pulls in modern offset and round offset profiles. Those lengths give the full-height grip typical of entrance doors, where the Rockwood 105 is a short grab pull at 5-1/2 inch center-to-center with 2-5/8 inch projection. Match the mounting hole layout to what is already drilled in the door leaf before switching between them.
22) What is a half-round push plate alternative if the Rockwood 105 will not fit the push side?
The Trimco 1041 is a heavy duty half-round push plate at 8 inch by 16 inch, which covers a wider band of the door face than a bar pull occupies. That is a push side solution rather than a substitute for the pull side, where the Rockwood 105 stands off the door with 1-7/8 inch clearance so the hand can get behind it.
How fast can I get the Rockwood 10532D delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Rockwood 10532D come with a warranty?
Absolutely. The Rockwood 10532D is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Rockwood 10532D?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Rockwood 10532D from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.