You may also like
ROCKWOOD 111 Door Pulls
Material: Stainless steel;
Finishes: US32D;
Fastner: 1/4 - 20 x 2-1/4" thru bolt & finish washer (standard 1-3/4" door);
Options:
- Back to back mounting in pairs — use BTB suffix and mounting type number (112BTB5)
- Concealed mounting single pulls — use C suffix and mounting type number (112C6)
- Advise if door thickness is other than 1-3/4"
- Heavy duty versions of most fastening types available – use suffix HD to fastening type number (112BTB5HD)
- See page B13 for mounting selection (standard duty 1/4 - 20)
- 2-1/2" Barrier Free clearance — use BF prefix (BF110)
- See page B27 for mounting selection (standard duty 1/4 - 20)
- Use Y prefix (YBF16) when ordering pulls with base plates, Y plate diameter is 1-1/4"; recommended for use on wood and glass doors.
ROCKWOOD OVERVIEW
Rockwood products are normally used on all types of institutional buildings, offices, retail, educational, detention, sports facilities, hotel and restaurant, and finer residences.
ENVIRONMENTAL MANAGEMENT
ASSA ABLOY is commited to protecting the quality of the environment as well as the health and safety of its employees, customers, and the community. Please see our Environmental Health and Safety Policy for details on how we are dedicated to this commitment.
RESOURCES & DOWNLOADS
Manufacturer Resources
Product Specs
- Product Group:
- Door Trim and Accessories
- Clearance:
- 2"
- Fasteners:
- 1/4 - 20 x 2-1/4" thru bolt & finish washer (standard 1-3/4" door)
- Subcategory:
- Push and Pull Plates, Door Pulls
- Product Subgroup:
- Door Pulls, Push and Pull Plates
- Product Type:
- Door Pulls
- ANSI/BHMA:
- ANSI A156.6, J401
- Commercial/Residential:
- Commercial
- Product Model:
- 111
- (CTC) Center-to-Center:
- 10"
- Product Projection:
- 3-1/2"
- Product Category:
- Door Trim and Accessories
- Product Substrate:
- Stainless Steel
- Department:
- Door Hardware
Rockwood 111-313 – Frequently Asked Questions
1) Will the Rockwood 111 door pull work on a 1-3/4 inch door?
Yes. The 111 ships with 1/4-20 x 2-1/4 inch thru bolts and finish washers sized for a standard 1-3/4 inch door, which is the usual commercial door thickness. Thru-bolt mounting means the fastener passes all the way through the door and lands in the opposing pull or a finish washer, so the door thickness has to match the bolt length. If your doors are thicker or thinner than 1-3/4 inches, say so when you order so the fastener length is adjusted.
2) Is 2 inches of clearance enough hand room, or do I need a barrier-free pull?
The standard Rockwood 111 gives 2 inches of clearance between the bar and the door face. Rockwood also builds a 2-1/2 inch barrier-free clearance version, ordered with a BF prefix, if your facility standard calls for the wider hand room. Gloved hands and heavy-traffic institutional openings are the usual reason to step up.
3) Can I get Rockwood 111 pulls mounted back to back on a glass or full-glass door?
Back-to-back mounting is available on the 111 family, ordered in pairs using the BTB suffix with the mounting type number. For glass or wood doors, Rockwood recommends the version with base plates, ordered with a Y prefix; the Y plate is 1-1/4 inch diameter and spreads the load at the fastener. Concealed mounting for a single pull is the C suffix.
4) Does the Rockwood 111 meet ANSI standards for a commercial pull?
The 111 is listed to ANSI A156.6, type J401, the standard covering architectural door trim. It is a commercial-grade product in stainless steel, which is what specifiers and institutional buyers ask for on schools, healthcare, hotels, and detention work.
5) What is the closest equivalent to the Rockwood 111 straight door pull from another manufacturer?
The Ives 8103HD is the nearest straight-pull match: a heavy duty straight door pull with a 1 inch round bar and through bolt mounting, the same 1 inch diameter grip and through-bolt fastening approach as the Rockwood 111, which mounts with a 1/4 - 20 x 2-1/4 inch thru bolt and finish washer for a standard 1-3/4 inch door. The ABH AB3300 is the other straight option, a 1.00 inch diameter commercial straight flat end pull. All three are straight-bar pulls rather than offset, so the grip geometry at the opening stays the same.
6) The Rockwood 111 has a 2 inch clearance. What pull should I use if I need more knuckle room on a heavily used door?
The Rockwood 111 straight pull carries a 2 inch clearance and a 3-1/2 inch projection. If the opening calls for an offset grip instead, the Ives 8145EZHD is a 45 degree offset door pull described as ADA compliant with heavy duty mounting hardware, and the Ives 8169 is a C style offset solid pull at 1 inch diameter with heavy duty mounting. Offset pulls carry the grip away from the door face rather than parallel to it, which changes how the hand enters the pull compared with a straight bar.
7) Which Rockwood 111 alternatives look similar but are not actually straight-bar door pulls?
Several items sit near the Rockwood 111 straight pull without being a substitute for it. The Trimco 1001-1 is a heavy duty push plate at 3 inches by 12 inches and the Trimco 1041 is a half-round push plate at 8 inches by 16 inches, both flat plates for the push side rather than a grip. The Trimco 1070 series is a classic push/pull plate at 3-1/2 inches by 15 inches, a plate-mounted assembly rather than a bare bar. The Cal-Royal PUL-175 is a night latch cylinder pull at 3-1/2 inch height in stainless steel, made to pull a door with a cylinder rather than to serve as a full-length grip. If the opening needs a 10 inch center-to-center bar, none of these fill that role.
8) I need a back-to-back pull set on a 1-3/8 inch door. Does the Rockwood 111 fit, or should I use something else?
The Rockwood 111 is fastened for a standard 1-3/4 inch door with 1/4 - 20 x 2-1/4 inch thru bolts and finish washers, and back-to-back mounting in pairs is ordered with the BTB suffix plus the mounting type number; door thickness other than 1-3/4 inch has to be advised at the time of order. If the door is thinner, the Deltana OHP620 off-set handle pull is supplied as a back-to-back set with a door thickness range of 1-1/8 inch to 1-3/8 inch. The Deltana SSPOBB24 and SSPORBB24 are also back-to-back sets, at 24 inches in modern offset and round offset forms.
9) What finishes does the Rockwood 111 straight pull come in?
Three finishes: US32D satin stainless steel, US28 anodized aluminum, and US313 dark bronze. US32D is the one that matches most commercial door hardware already hanging in an institutional building, so it is the safe pick when you are adding pulls to an existing fleet of openings.
10) Do I need a heavy duty version of the Rockwood 111 for a high-traffic entrance?
Standard 111 mounting is 1/4-20 thru bolt. Rockwood offers heavy duty versions of most fastening types by adding an HD suffix to the fastening type number, which is worth specifying on entrances that get pulled on hard all day. If you want a heavier bar from another line, the Ives 8103HD is a 1 inch round straight pull with through-bolt mounting listed as heavy duty, and the Ives 8102HD uses a 3/4 inch round bar with 1-1/2 inch clearance.
11) Should I use a straight pull or an offset pull on my door?
The 111 is a straight bar pull, 1 inch diameter, 10 inch center to center, with the bar parallel to the door face. Straight pulls suit narrow stiles and doors where you want a clean vertical grab. Offset pulls angle the bar away from the face and give a more natural wrist position on heavy doors; if that is what you want, the ABH AB3310 flat end offset and AB3330 round end offset cover it, the Ives 8145 is a 45 degree offset in an ADA compliant EZ series, and the Ives 8169 is a 1 inch diameter C style offset.
12) I need a matching push plate for the other side of the door. What pairs with a Rockwood 111 pull?
The 111 is a pull only, so the push side needs a separate plate. From what we stock, the Trimco 1001-1 heavy duty push plate is 3 by 12 inches, the Trimco 1041 half-round push plate is 8 by 16 inches, and the Trimco 1070 Series classic push/pull plates run 3-1/2 by 15 inches. Match the plate finish to the pull finish you order.
13) The Rockwood 111 is a 10 inch CTC pull. What do I use when the opening calls for a longer grip?
The Rockwood 111 is built at 10 inch center-to-center. For longer runs, the Deltana SSP1210 is a 12 inch contemporary pull for single side mounting, and the Deltana SSPOBB24 and SSPORBB24 are 24 inch back-to-back pulls in modern offset and round offset styles. The ABH AB3330 series offset round end pull is offered with custom length options when a specific length is called out on the drawing.
14) For a restroom door, is the Rockwood 111 the right pull or is there a purpose-built option?
The Rockwood 111 is a straight stainless steel commercial pull at 10 inch center-to-center with a 2 inch clearance, which suits a general commercial opening. Where the specification is written for a restroom specifically, the Trimco 1035 Ultimate Restroom Pull is a heavy duty pull made for that application. Both are heavy-traffic commercial parts; the difference is that the Trimco 1035 is designed around the restroom door and the Rockwood 111 is a general-purpose straight pull.
15) I am standardizing offset pulls across a facility. What are the offset alternatives to the straight Rockwood 111?
The Rockwood 111 is a straight-bar pull. On the offset side, the ABH AB3310 is an offset flat end pull handle for commercial grade surface mount, the ABH AB3330 series is an offset round end pull with custom length options, the Ives 8169 is a C style offset solid pull at 1 inch diameter with heavy duty mounting, and the Ives 8145EZHD is a 45 degree offset pull described as ADA compliant with heavy duty mounting hardware. Flat end and round end describe how the bar terminates, which is the detail to fix when every door in the facility has to look alike.
16) What is the difference between the Rockwood 111 and the ABH AB3300 for a wood or glass door?
Both are 1 inch diameter straight commercial pulls; the ABH AB3300 is an AB3300 series straight flat end pull handle at 1.00 inch diameter. The Rockwood 111 can be ordered with base plates using the Y prefix, where the Y plate diameter is 1-1/4 inch, and that base plate arrangement is recommended for use on wood and glass doors. If the substrate is wood or glass, the base plate option is the detail to specify.
17) Is a stainless Rockwood 111 pull suitable for a hospital, school, or hotel entrance?
That is exactly the intended use. Rockwood trim goes on institutional buildings, offices, retail, education, detention, sports facilities, hotels and restaurants. The 111 is solid stainless steel, thru-bolted rather than surface-screwed, and conforms to ANSI A156.6 J401, which is what a facility spec usually calls for on door trim.
How fast can I get the Rockwood 111-313 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Rockwood 111-313 come with a warranty?
Absolutely. The Rockwood 111-313 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Rockwood 111-313?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Rockwood 111-313 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.