Schaub 416 6" Center to Center Lumiere Transitional Cabinet Pull

Yes. The Schaub 416 Lumiere Transitional pull is drilled on 6 inch centers, so it drops onto an existing pair of holes bored 6 inches apart with no new drilling. Overall length is 8 inches, which leaves about an inch of pull past each screw hole, so check you have that much clear face on the drawer front or door stile.

The 416 uses 8/32 thread screws in a 1 inch length. That covers a standard 3/4 inch drawer front or door with thread to spare. If you are going through a thicker slab front, a drawer box face plus applied front, or a panel with a backing layer, you will need longer 8/32 machine screws, since the supplied 1 inch length runs out fast once material thickness exceeds about 3/4 inch.

The Schaub 416 Lumiere Transitional pull is a 6 inch center-to-center pull with an 8 inch overall length, so it will not land on a 4 inch drilling. The Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, which matches that hole pattern directly. For smaller drawer drillings, the Trimco 553 series drawer pulls are 3 inch center to center and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96mm center-to-center options.

Projection is 1-1/4 inches, measured from the cabinet face to the front of the grip. That is enough hand clearance for a gripped pull on a drawer bank, and it is the number to watch in a galley kitchen or a tight island run where drawer fronts face a walkway. The base sits 7/8 inch at the mounting posts.

Six finishes: Polished Brass, Satin Brass, Polished Nickel, Satin Nickel, Polished Chrome, and Polished Rose Gold. The pull is solid brass underneath all of them, so the plated and lacquered finishes sit on a brass body rather than a zinc casting. For a multi-unit or whole-house spec, order the full quantity in one go so all pieces come from matched finish runs.

Staying in solid brass, the Omnia 1970 is a forged solid brass cabinet pull with the same 1-1/4 inch projection, and the Omnia 1969 and 1971 are forged brass pulls at 1-3/16 inch projection if you want the grip a touch closer to the face. The Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inches, a shorter, squarer look than the Lumiere. The Schaub 416 itself is transitional styling rather than strict modern.

The 416 belongs to Schaub's Lumiere Transitional collection, so knobs and other sizes within that same collection are the way to keep the profile and finish consistent across doors and drawers. Emtek also carries Schaub Collection cabinet hardware, including the Emtek 8405 Select pulls and the Bar, Alexander, and Art Deco series, if you are pulling a coordinated program together from a single ordering point.

Two directions from the Schaub 416, which is a transitional-style pull in the Lumiere Transitional collection: for a more decorative period look, the Emtek Art Deco Cabinet Pull in the Art Deco series and the Emtek Alexander Cabinet Pull in the Alexander series are both Schaub Collection cabinet knob/pulls. For a plainer modern line, the Omnia 1969 and Omnia 1971 are modern cabinet pulls in forged solid brass, each with a 1-3/16 inch projection versus the 1-1/4 inch projection of the 416.

The Schaub 416 is a 6 inch center-to-center pull requiring two bores; a knob needs only one. For single-bore openings, the Orca Hardware Bachelor Collection CK-15030 is a round cabinet knob at 1-1/4 inch diameter, the CK-16030 is a round ring cabinet knob at 1-1/4 inch diameter, and the Blackcomb CK-17025 is a square cabinet knob at 25mm diameter. Note the Schaub 416 is solid brass, while those Orca knobs are catalogued by collection rather than a matching base material.

For a square profile, the Deltana SBP35 is a modern square bar pull at 3-1/2 inch in heavy-duty solid brass, which shares the solid brass base material of the Schaub 416 but is a square bar form at a shorter span than the 416's 6 inch center to center. Among Emtek's Schaub Collection offerings, the Bar Cabinet Pull is catalogued as a cabinet knob/pull in the Bar series for a straight bar look.

Solid brass is the base material on the 416 Lumiere pull, not zinc or plated die cast. That matters for rental turns and high-traffic kitchens, where thin plating over soft castings is what usually fails first at the grip. All six finish options are built on the same brass body.

No. The SDC SP50 is a 50MM spindle categorized under door controls, not cabinet hardware, and it has no role in mounting a cabinet pull. The Schaub 416 is a cabinet pull that mounts with 8/32 x 1 inch screws.